It's twenty minutes before the end of the shift and the case erector on line two has jammed again. A flap has caught, a carton is folded halfway into the guide rails, and the conveyor behind it is filling up. The carton is right there, an arm's length inside the guard, and the machine has stopped. It would take ten seconds to reach in and pull it out.
That ten-second reach is what this post is about. A stopped machine and a safe machine aren't the same thing, and the gap between them is where lockout earns its keep. Below is how we'd think about lockout for the everyday job of clearing a jam, what each step on our Machine Pre-start / LOTO Checklist is really asking, and how to keep the whole thing quick enough that people don't feel tempted to skip it.
"It's stopped" isn't the same as "it's safe"
When a machine faults on a jam, it usually stops because a sensor told it to. That sensor can clear. Someone else can hit reset, or a photo-eye blocked by the carton can see daylight the moment it moves, and some machines pick up exactly where they left off.
And even with the power genuinely off, plenty of machines keep energy in reserve:
- Air cylinders that are still holding pressure, so a pusher or clamp can move when a blockage is cleared.
- A belt or chain under tension, which springs back when the jammed item comes free.
- A raised platen, gate or arm that's being held up by hydraulics or a brake rather than a mechanical block.
The jam itself is often what's holding that energy back. Pull the carton and you release it, with your hand in the way.
Walking through the lockout steps
The template's tick list is labelled LOTO isolations applied. It has five items. Here's what each one means when the job is a jam rather than a planned rebuild.
Energy sources identified. Before anyone touches a lock, name every source the machine has: the main electrical isolator, the air supply, any hydraulics, gravity, anything under tension. A case erector might have a main isolator and an air dump valve. If the operator isn't sure, that's the moment to get the shift lead or maintenance, not to guess.
Locks / tags applied. Each person working inside the guarding puts their own lock on each isolation point. One lock for the whole crew means someone can finish, remove it and restart the machine while a colleague is still inside.
Stored energy released. Bleed the air, lower or block anything raised, and let anything moving come to a full stop. This is the step people forget most often on jams, because the machine looks still. If the pressure gauge on the air line still shows pressure, it isn't done.
Try-start confirmed zero energy. With locks on and everyone clear, press start. Nothing should happen. Then return the control to off. This is the step that catches the wrong isolator: the panel labelled "line 2" that actually feeds line 3, or the second supply nobody knew about. It takes a few seconds and it's the only step that actually proves the isolation works.
Affected people notified. The operator upstream, the person at the end of the line and the shift lead should all know the machine is locked out and who's inside.
Only then does anyone reach in for the carton.
The pre-start half matters too
The same form has a second tick list, Pre-start checks (tick if OK), which covers the handover back to production:
- Guards fitted & secure. Any guard opened to reach the jam goes back on, every fastener included.
- Emergency stop tested, so you know it works before the machine runs again.
- Area clear of debris. The torn carton, any loose flaps and any tools all come out.
- PPE worn for task.
- Work instruction / SOP available, so the next person to clear this jam does it the same way.
Then comes the question that decides it: Safe to operate / work? The answer is either Yes or No — do not proceed. If the jam turned out to be caused by a worn guide rail or a sticking cylinder, the honest answer is no, and the machine stays locked until maintenance has looked at it.
Making it quick enough to happen at 2:40 p.m.
Nobody skips lockout because they think it doesn't matter. They skip it because the line is backing up and the isolator is around the back of the machine. A few things make the right way the easy way:
- Put the fill link at the isolation point. A QR code on the isolator or the machine's control panel, labelled with the asset number, means the form opens on the operator's phone with nothing to look up.
- Make locks easy to reach. A lock station near each line, with personal locks and tags, takes away the walk to the maintenance office.
- Back the person who stops the line. If a supervisor thanks someone for locking out rather than asking why the line was down for six minutes, people will keep doing it.
Filling it on a phone at the machine
The form asks for the Date and Time, the Machine / asset ID (whatever's on the plate, like "CE-02" or "Palletiser 1"), and the Operator name. Then come the two tick lists and the Safe to operate question. The Notes / defects box is for anything useful later, like "carton flap caught on left guide rail again, third time this week" or "air dump valve slow to bleed".
It finishes with two signatures, an Operator signature and a Supervisor signature, both signed with a finger on the screen. The supervisor signature means a second person has seen the machine before it goes back into production. The required fields mean the form can't be sent with the lockout steps left blank. People who only fill the form don't need an account; they just need the link.
If you'd like a photo of the jam point or a worn part, add a photo field to the template in the builder before you share the link.
What the records tell you afterwards
Every submission lands in Reports. The obvious use is evidence: when a client, auditor or your own management asks how isolation is controlled, you can export the records as PDF or CSV and show which machine was locked out, when, by whom and what they found.
The less obvious use is spotting repeat jams. If line two's case erector shows up in the LOTO records four times a week with "flap caught on left guide rail" in the notes, that isn't an operator problem. It's an adjustment, a worn part or a carton supply issue, and fixing it removes the reach-in risk altogether.
You'll find related templates on the Manufacturing page, including the Quality Non-Conformance form for when a jam turns out to be a carton or component problem, and the Near Miss Report for the time someone nearly did reach in.
If you'd like to try it, start a free trial, load the Machine Pre-start / LOTO Checklist from Templates in the builder, and put a fill link on the machine that jams most often. Give it a couple of weeks and see what the notes tell you.