It's half past three on a Thursday. A fitter has been grinding brackets on a mezzanine in an occupied warehouse. The cut finishes earlier than planned, the angle grinder goes back in the bag, and the fire watch — who'd been standing with an extinguisher for the last hour — walks downstairs to grab a coffee. The permit was signed that morning. The area looked clear. Job done, right?
Twenty minutes later someone smells smoke in the void above the ceiling tiles. A hot slag flake had dropped into insulation nobody could see from the floor. The grinding stopped at 3:30. The fire started closer to four.
This post is about the part of a hot work permit that usually gets treated as optional: the named fire watch that stays after the last spark, for the duration you actually wrote down.
Why the permit often ends when the tools do
Most trades and contracting crews already know they need a hot work permit for welding, cutting or grinding. The form gets filled, the authoriser signs, and work starts. Where it falls over is the end of the job:
- The person doing the hot work packs up and assumes the watch is finished because the sparks have stopped.
- The fire watch was never clearly named, so whoever was nearby drifts off when the noise stops.
- The post-work duration was left blank, or everyone vaguely remembers "about half an hour" without writing it down.
- The job finished early, so the watch feels like wasted time against a busy afternoon.
None of that is people trying to cut corners on purpose. It's what happens when authorising the work gets all the attention, and the quieter part afterwards gets treated as a courtesy. Smouldering fires don't care that the grinder is already in the ute.
What goes on the permit before anyone strikes an arc
Our Hot Work Permit template is short enough to fill on a phone at the workface. Here's how each field earns its place, especially the ones that matter after the work stops.
Date, Start time and End time. When the hot work is authorised for. The end time is a planning number, not permission to walk away the second the last cut finishes. If the job wraps early, the fire watch still runs from when the sparks actually stop.
Location of hot work. Be specific: "Mezzanine bay 4, north side above racking", "Plant room B, pipe run behind AHU-3". Vague locations make it harder for anyone checking later to know where the watch should have been looking.
Hot work type. Pick from Welding, Cutting / grinding, Soldering / brazing, Open flame, or Other. Grinding and cutting throw sparks further than people expect; welding and open flame leave heat in the work itself.
Person doing hot work and Fire watch name. Two different people, written down. The fire watch is not "whoever's free" and not the same person holding the torch. If the named watch has to leave, the work pauses or a replacement is named first.
Precautions completed. Tick what's actually done: Area cleared of combustibles, Fire extinguisher on hand, Sparks contained / screens, Smoke / heat detection considered, and PPE suitable for task. On detection, that means you've thought about whether detectors need isolating — and that they get turned back on before the watch ends.
Fire watch duration after work. This is the field that stops the coffee-break walkaway. Choose 30 minutes, 60 minutes, or As specified in notes. Pick it before work starts. Higher-risk spots — voids, occupied buildings, plant rooms, insulation — often need the longer watch.
Notes / special conditions. Anything the watch needs to know: "Ceiling void above; lift a tile every ten minutes", "Detection isolated on zone 3 — restore before leaving", "Do not restage combustibles until watch ends".
Photo of work area (optional). A quick shot of the cleared area before sparks fly helps if someone later asks what the setup looked like.
Authoriser signature and Hot work operator signature. Finger-signed on the screen. The authoriser is saying the precautions and fire watch plan are good enough to start; the operator is saying they'll work to that plan, including the watch after they finish.
What the fire watch actually does after the last spark
When cutting or welding stops, the job isn't closed. The named fire watch stays for the duration on the permit and keeps looking for heat, smoke and smell — including places sparks could have travelled: cable trays, ceiling voids, behind screens, under mezzanine decking.
A simple rhythm helps:
- Stay in the work area for the full 30 or 60 minutes (or whatever you put in the notes).
- Check the obvious landing spots for sparks every few minutes, not just once at the end.
- Keep the extinguisher where you can reach it without hunting.
- Don't restage combustibles until the watch time is up.
- If detection was isolated for the job, make sure it's back before you leave.
If the operator finishes early, the watch still runs from the real end of hot work — not from the planned end time. Write the actual finish in the End time field or the notes so the record matches what happened.
Filling it on a phone on site
Hot work permits that live on a clipboard in the site office get filled in after the fact, or not at all for "quick" grind jobs. A fill link on the supervisor's phone — or a QR code at the permit board — means the authoriser and operator can complete it at the mezzanine before the first cut.
People who only fill the form don't need an account. They open the link, pick the hot work type, name the fire watch, choose the post-work duration, tick the precautions, and sign. The submission is the permit record.
What the record shows afterwards
Every completed permit lands in Reports. Over a few weeks you can see which sites run a lot of cutting and grinding, whether fire watches are actually named, and whether the post-work duration is being chosen or left as an afterthought. Patterns turn up fast — the same plant room always on 30 minutes when the void wants 60, or end times that still match the plan when the work stopped early.
If a principal, insurer or your own management asks how hot work is controlled, you can export the permits from Reports as PDF or CSV: who did the work, who was fire watch, what precautions were ticked, and how long the watch was meant to stay.
You'll find related templates on the Trades & contracting page, including Permit to Work and Toolbox Talk for the same busy cutting days.
If you'd like to try it, start a free trial, load the Hot Work Permit from Templates in the builder, and use it on the next grind or weld where someone might otherwise walk away when the noise stops. See whether naming the fire watch and picking 30 or 60 minutes changes what happens after the last spark.